## Servicios Personalizados

## Revista

## Articulo

## Indicadores

- Citado por SciELO

## Links relacionados

- Similares en SciELO

## Compartir

## Latin American applied research

##
*versión impresa* ISSN 0327-0793

### Lat. Am. appl. res. vol.41 no.1 Bahía Blanca ene. 2011

**ARTICLES**

**Tensorial equations for three-dimensional laminar boundary layer flows**

**M. Storti, J. D'Elía and L. Battaglia**

Centro Internacional de Métodos Computacionales en Ingeniería (CIMEC)

Instituto de Desarrollo Tecnológico para la Industria Química (INTEC)

Universidad Nacional del Litoral -CONICET

Güemes 3450, 3000-Santa Fe, ARGENTINA

ph.: (54342)-4511 594/5, fx: (54342)-4511 169

(mstorti, jdelia)@intec.unl.edu.ar, lbattaglia@ceride.gov.ar, http://www.cimec.org.ar

**Abstract - **Tensorial equations are derived for a laminar and attached boundary layer flow with null pressure gradient in the normal direction to a smooth three-dimensional surface. An incompressible, isothermal and viscous fluid of Newtonian type is assumed. Covariant derivatives in the three dimensional Euclidean domain are employed, where the surface curvature terms are implicitly included in the Christoffel symbols with the aim of writing the boundary layer equations in an invariant form irrespective to the particular choice of the coordinate system. These equations are covariant under a linear coordinate transformation on the two surface coordinates, and a scaling along the normal direction to the surface. As a test case, the boundary layer near a sphere in an axisymmetrical steady flow is numerically computed using a pseudo-spectral approach.

**Keywords** - Boundary-Layer Equations; Laminar Steady Flow; Incompressible Viscous Fluid; Three-Dimensional Surfaces; Tensor Analysis.

**I. INTRODUCTION**

As it is well known, mechanical devices may require the calculation of fully three-dimensional boundary layers (e.g. see Schlitchting and Gersten, 2004), as those associated with flow inside turbomachines (Lakshminarayana, 1995), horizontal-axis wind turbine blades (Prado, 1995), laminar flow technology (Stock, 2006) or aerospace technology (Dwoyer et al., 1978), among other cases. The laminar boundary layer equations for three-dimensional surfaces are well-known (e.g. see Cebeci and Cousteix, 1999; Dey, 2001). In any case, there are curvature effects that do not disappear as they do in the two-dimensional case (Reed and Lin, 1993). In fact, these curvature effects are present through the (local) principal curvatures of the surface. If one of them is null the boundary layer equations are independent of the curvature effects, as in planes, yawed infinite cylinders or wings (Pai, 1956).

There is nothing special about a particular system of coordinates, so a physical or geometrical law behind the equations for the boundary layer flow should be independent of them. The related equation is often first presented in Cartesian coordinates, and its differential form is typically presented in a coordinate independent system using vector notation based on the nabla operator (German, 2007). With the coordinate invariant form known, the solution is usually approached by selecting a particular coordinate system, e.g. Cartesian, cylindrical, or spherical ones. In order to determine a differential equation in a selected coordinate system, the nabla operator is expressed in terms of partial derivatives with respect to the chosen coordinates, or alternatively, the related operators are obtained through a tedious coordinate transformation from the well known Cartesian form. In this way, coordinate independent expressions of these equations can be cast in a specific form from which analytical and numerical solutions can be pursued. An alternative although equivalent approach to posing coordinate invariant equations is to employ a tensorial representation. As it is well known, a tensor equation is a coordinate invariant equation where the monomials have to be tensors of a same order and, in component format, all terms must contain the same free indices. Thus, tensorial equations, like those written in terms of the nabla operator, are form invariant, or covariant, with respect to regular curvilinear coordinate transformations. As in the case with the nabla form, operations such as the gradient and divergence are well defined. However their representation is in terms of the resource of tensor calculus. Besides the fact that both approaches are equivalents, the tensor approach often provides a more tractable and compact method for dealing with transformations among regular coordinate systems, since the relationships between the differential equation and the geometry can be a bit more clean than the nabla operator approach. For instance, a differential equation can be cast in terms of a particular set of coordinates through the specification of the metric tensor corresponding to the coordinate system, where all of the differential operators depend exclusively on metric tensor and combinations of its partial derivatives, i.e. the Christoffel symbols. Although determining the metric tensor and Christoffel symbols for a regular but arbitrary coordinate system is not a simple task, it is often appreciably less challenging and tedious than determining the gradient and divergence operators by direct transformation of the partial derivatives. This is especially true for cases when these operators are not tabulated for the desired coordinate system, whereas the tensor components and Christoffel symbols may also not be tabulated. Nevertheless, a straightforward recipe is available through which they can be calculated with tensor analysis (German, 2007).

In another way, Panaras (1987) gave the formulation of the unsteady, compressible Navier-Stokes covariant equations in general non-orthogonal curvilinear coordinates and thereafter a discussion follows about the terms which could be omitted in a thin shear-layer formulation. The present work considers steady, incompressible fluid flow using covariant derivative in an orthogonal coordinate system but it is not a special case. The main differences are: (i) Panaras wrote the boundary layer equations in a full way with several surface curvature terms explicitly given, while in this work, they are implicitly included in the Christoffel symbols of the covariant derivatives with the main aim of putting the boundary layer equations in invariant form irrespective of the choice of the coordinate system, and (ii) a slight difference exists in the choice of the normal coordinate to the surface. As it is well known in standard boundary-layer engineering, the surface curvature terms (i.e. the normal pressure gradient) are the first terms to be added when Prandtl basic equations are extended to the three dimensional case and there are many expressions proposed in literature, partially due to the several approximations that can be performed with the curvature terms. However, it is cumbersome to check about the physical invariance of the proposed equations. Therefore, in order to obtain a more physical picture and an easier verification, it would be convenient to place the surface curvature terms only in the covariant derivatives instead of displaying them in boundary layer equations.

On the other hand, a full numerical solution of the Navier-Stokes equations for high Reynolds numbers is nowadays a standard approach, like those based in the Reynolds Averaged Navier-Stokes (RANS) equations (Wilcox, 1998), Large Eddy Simulations (LES) (Sagaut, 2001) and Direct Numerical Simulations (DNS) (Pope, 2003), among several approaches. Nevertheless, three-dimensional boundary layers and boundary layer separation are still areas where boundary layer computations may be seen as a complementary tool, for instance, coupled viscous-inviscid computations for wind turbine airfoil flows (Bermúdez *et al.*, 2002), unsteady flows in turbomachinery (Epureanu *et al.*, 2001), unsteady interaction with outer transonic flows (Bogdanov and Diyesperov, 2005), flows past moving bands (Frondelius et al., 2006), as well as oscillatory boundary layers attached to deformable solid walls (Nicols and Vega, 2003).

The boundary layer equations are also proposed as alternatives to the classical convective outlet boundary condition heavily used for wall-bounded laminar/turbulent flows (Fournier *et al.*, 2008). In fact, three-dimensional boundary layer methods are likely to be both more accurate and less computationally expensive than a full numerical solution of the Navier- Stokes equations. They can be performed using classical approaches, as the integral ones used in Karimipanah and Olsson (1993), where the effects of rotation and compressibility on rotor blade boundary layers are studied. Other methods are finite differences (Anderson, 1985), finite elements (Schetz, 1991) and pseudo-spectral approaches (Storti, 1998). In any case, the solutions can be used for testing more elaborated computational codes as those that directly solve the Navier-Stokes equations in several contexts, for instance, for modelling free surface flows (D'Elía *et al.*, 2000; Battaglia et al., 2006; Storti *et al.*, 1998), added mass computations (Storti and D'Elía, 2004) or inertial waves in closed flow domains (D'Elía *et al.*, 2006).

The present work develops a covariant derivation of the boundary layer equations in tensorial form valid for three-dimensional, steady and laminar boundary layers with null-pressure gradient in the normal direction to the surface. They are written in an orthogonal curvilinear coordinate system, defined by two surface coordinates plus a normal one to the surface, such as, (i) they are covariant under a coordinate transformation on the two intrinsic surface coordinates and a scaling one along the normal coordinate to the body surface; (ii) the surface curvature terms are implicitly present in the covariant derivatives and not in the displayed equations as opposed to the more traditional way that typically includes the surface curvature, surface principal curvatures or related terms in the boundary layer equations; (iii) it only remains the surface metric tensor in the continuity equation. As a practical use of the proposed covariant formalism, the steady and laminar three-dimensional boundary layer flow near a moving sphere of an incompressible and viscous fluid is performed as a test case using a pseudo-spectral approach, first without a rotation and later with a steady spin rotation.

**II. SURFACE AND EXTENDED COORDINATES**

In all this work, Latin affixes run in the threedimensional Cartesian space, e.g. *i* =1, 2, 3, the Greek ones run on the two-dimensional surface, e.g. *α* =1, 2, while upper and lower affixes denote contravariant and covariant components of tensors of any range (Aris, 1989; Smith, 1963). Lower and upper letters denote dimensionless and dimension quantities, respectively. The basic ones are the coordinates *x ^{i}* =

*X*, velocities

^{i}/ L*u*= /

^{i}*U*/

^{i}*U*and pressure

*p*=

*P*/ (

*ρU*), where

^{2}*U*,

*L*and

*ρ*are typical speed, length and fluid density, respectively, while, regarding incompressibility of the fluid,

*ρ*is constant.

It is assumed that the body surface *Γ* is smooth enough to be represented by a coordinate grid on the surface itself, expressing the position of a surface point in terms of the dimensionless surface coordinates. Thus, the surface equation has the form *x ^{i}* =

*x*(

^{i}*η*,

^{1}*η*), where

^{2}*η*,

^{1}*η*are the surface coordinates, the intrinsic ones, while the lines

^{2}*η*= constant and

^{1}*η*= constant are the coordinate lines. The Cartesian coordinates

^{2}**=(**

*y**y*

^{1},

*y*

^{2},

*y*

^{3})

^{T}∈ , for a generic point

**on the surface**

*y**Γ*can be expressed as a function of the surface coordinates

**=**

*y***(**

*y**η*

^{1},

*η*

^{2}), see Fig. 1, where (...)

^{T}denotes the transpose. An extended coordinate system (

*η*

^{1},

*η*

^{2},

*η*

^{3}) is introduced as a threedimensional curvilinear one for extending the surface coordinates to the three-dimensional space where the body is immersed, where the η

^{3}-coordinate is normal to the body surface. When the generic point

**is over the surface, the coordinates are (**

*y**η*

^{1},

*η*

^{2},

*0*), and when it is at any place in the three-dimensional space, the coordinates are

**x**=

**+**

*y***, where**

*nδ***=**

*n***(**

*n**η*,

^{1}*η*) is the exterior unit normal on the surface at point

^{2}**=**

*y***(**

*y**η*

^{1},

*η*

^{2}), with

**∈**

*y**Γ*, while

*δ*=

*δ*(

*η*

^{1},

*η*

^{2}) is a dimensionless boundary layer thickness (or expansion parameter), with . The Jacobian of the transformation from the (

*x*

^{1},

*x*

^{2},

*x*

^{3})system to the (

*η*

^{1},

*η*

^{2},

*η*

^{3}) one is assumed as regular in all the domain and it is given by

*J*=

_{ij}*∂x*/

_{i}*∂η*, for 1 ≤

_{j}*i, j*≤ 3, which are written as the matrix

*J*=[

*J*

_{1}

*J*

_{2}

*J*

_{3}] ∈ whose columns are

(1) |

**Figure 1**: Dimensionless coordinates: surface intrinsic(*η ^{1}*,

*η*) on the smooth surface

^{2}*Γ*, the normal coordinate η

^{3}and the point

**=(**

*y**y*

^{1},

*y*

^{2},

*y*

^{3}) ∈

*Γ*in the three-dimensional Cartesian space .

**III. SPATIAL AND SURFACE METRIC TENSORS**

The metric tensor is an intrinsic quantity that relates measurements performed inside a same domain, spatial or surface one. Note that in this work there is a spatial metric tensor *g*_{ij} for the three-dimensional domain, with 1 ≤ *i*, *j* ≤ 3, as well as a surface metric tensor *a*_{αβ} for the body surface, with 1 ≤ *α*, *β* ≤ 2. The main attention in this work it is focused on the former one. Both of them are assumed as smooth, symmetric and positive definite tensors.

**A. Partition of the spatial metric tensor**

The spatial metric tensor can be expressed in covariant *g _{ij}* or in contravariant

*g*components, taking in the first case the form

^{ij}(2) |

where *x*,_{i} = *∂x* / *∂η*^{i}. The tensor *g _{ij}* can be split in surface

*g*, normal

_{αβ}*g*

_{33}, and mixed

*g*

_{α3},

*g*

_{3α}tensor components. The corresponding covariant and contravariant matrices are

*g*

_{ij}≡ [

*g*] and,

_{ij}*g*≡ [

^{ij}*g*], respectively, and they are related by

^{ij}*g*

^{ij}= (

*g*)

_{ij}^{−1}, where (...)

^{−1 }denotes the inverse. The metric tensor partition suggests the corresponding matrix one

(3) |

where 1 ≤ *i*, *j* ≤ 3 for the extended coordinates, and 1 ≤ *α*, *β ≤* 2 for the surface coordinates, with *g*_{αβ} ∈, *g*_{α3} ∈ , *g*_{3β} ∈ , and *g*_{33} ∈ .

**B. Asymptotic orders in the covariant and contravariant spatial metric tensor**

The asymptotic orders in the covariant *g _{ij}* and contravariant

*g*spatial metric tensor with respect to the expansion parameter

^{ij}*δ*, with are inferred in Appendices A. and B., and they are summarized in Table 1, where

*a*

_{αβ}is assumed as a regular tensor.

**Table 1**: Covariant *g _{ij}* and contravariant

*g*spatial metric tensor components as a function of the expansion parameter

^{ij}*δ*, with .

** C. Asymptotic orders in the Christoffel symbols**

It is necessary to consider the Christoffel symbols since they appear in the expressions for the covariant derivatives. As it is well known, they have not got a tensor character, that is, they are not transformed with a tensorial law under a linear coordinates transformation (Smith, 1963), and they can be calculated with

(4) |

for the first kind and

(5) |

for the second kind. It is noted that, as the metric tensor *g _{ij}* is assumed as a symmetric one, these symbols are also symmetric in the lower affixes and consequently the torsion tensor is null, that is, the spatial and surface domains are torsionfree (Morgan, 1993). There are six types of these symbols depending on whether the affixes

*i*,

*j*,

*k*are on the smooth surface (

*η*

^{1}or

*η*

^{2}) or on the normal

*η*

^{3}coordinate. The asymptotic order of the Christoffel symbols with respect to the expansion parameter

*δ*, with , are estimated from the order of the spatial metric tensor in Appendices E. and F., and they are summarized in Table 2. Note that there is only one special case given by the symbol {3,

*β*γ} =

*O*(

*δ*

^{−1}), while the remaining ones are

*O*(

*δ*) or

*O*(

*δ*

^{2}).

**Table 2**: Order of the Christoffel symbols of first and second kind as a function of the expansion parameter *δ*, with .

** IV. NAVIER-STOKES EQUATIONS IN CURVILINEAR COORDINATES**

The dimensionless Navier-Stokes equations for a laminar, isothermal and steady flow without body forces of an incompressible and viscous fluid of Newtonian type with constant physical properties, are written in the extended coordinate system (*η*^{1},*η*^{2},*η*^{3}) as

(6) |

see for example Aris (1989), Sec. 8.22, and Spurk (1997), Sec. 4.1.3, which are the momentum and the continuity equations, respectively, *u ^{k}* is the

*k*-component of the flow velocity expressed in contravariant components, while

*Re = UL / ν*is the Reynolds number, where

*ν*is the fluid kinematic viscosity. It should be noted that as the pressure

*p*is a scalar field, then, its gradient can be written as

*p*

_{,j}=

*∂p*/

*∂η*

^{j}. For further use, the first and second covariant derivatives of a smooth vector field

*v*

^{k}are respectively computed with (see for example Smith (1963))

(7) |

** A. Tangential component of the momentum equations**

The tangential components of the momentum equations to the wall surface, are extracted from (6) as

(8) |

In Appendix C. it is shown that the convective, reduced pressure and viscous terms in Eq. (8) have the asymptotic orders

(9) |

Retaining the leading terms in Eq. (9), the tangential components of the momentum equations are reduced to

(10) |

** B. Normal component of the momentum equations**

The normal components of the momentum equations to the wall surface are taken from (6) as

(11) |

In Appendix D. it is shown that the convective, reduced pressure and viscous terms in Eq. (11) give the asymptotic orders

(12) |

and

(13) |

respectively. Comparing Eqs. (12,13) it follows that

(14) |

which is equivalent to the well known assumption in boundary layer analysis at zero order that the pressure gradient is negligible along the direction normal to the wall.

**C. Continuity equation**

The divergence of the velocity *u*^{k}can be calculated(e.g. see Aris (1989), Sec. 7.56) with

(15) |

since *g*^{0}= *a*^{0}*δ*^{−2 }+ *O*(1), where *g *= det(*g ^{ij}*) and

*a*

^{0}= det(

*a*

^{αβ}) are the determinant of the spatial and surface metric tensors, respectively. The equation (15) can be split and rewritten as

(16) |

** D. Tensorial equations for a three dimensional laminar boundary layer flow**

Finally, dimensionless covariant equations for a steady, laminar, attached and three dimensional boundary layer flow with null pressure gradient in the normal direction to the body surface are given by collecting Eqs. (10, 14, 16),

(17) |

In practical computations, it could be more convenient to put the pressure gradient *p*_{,α} = *∂p*/*∂α* in the form where *v* are the contravariant components of the outer (inviscid) velocity field, e.g. see Storti (1998).

**V. NUMERICAL EXAMPLE**

As a single application of the covariant three dimensional boundary layer equations given by Eq. (17), an axially symmetric flow past a sphere of radius A is numerically solved using a pseudo-spectral like approach. The numerical method is based on Fourier expansion in the lateral transformed coordinate, similar to the transformation that leads to the polynomial Tchebischev expansion in finite intervals, although more appropriate to semi-infinite intervals in such a way that no extra parameter is needed for the outer boundary of the layer. A scaling is applied to the coordinate normal to the body surface with an innovation based on the computed boundary layer thickness without assuming a priori variation for it. Thorough details about this computation and other flow tests including cones, yawed flat plates and circular cylinders were given in Storti (1998) so that only a brief account is given here.

The sphere is immersed in an incompressible and viscous fluid of Newtonian type, with kinematic fluid viscosity *ν* and fuid density *ρ*. Two flow cases are considered.

The first flow case is a sphere moving with constant velocity U∞ and no rotation, where two approximations performed for the base flow on the body surface ** V** = (

*V*

^{1 }, 0, 0), with

*V*

^{1 }=

*V*

^{1}(

*θ*), where

*θ*=

*Y*

^{1}/

*A*is the polar angle from the forward stagnation point

*S*, and

*Y*

^{1}is the curvilinear coordinate along the wall measured from the same point, see figure 2.

**Figure 2**: Curvilinear coordinates *Y* ^{1 }, *Y* ^{3 }and polar angle *θ* = *Y* ^{1}/*A*, measured from the forward stagnation point *S* on a sphere of radius *A*, the generic point on the body surface is *P* (*Y* ^{1 }, 0).

On one hand, the first approximation assumes the potential velocity profile *V* ^{1 }= (3/2) *U*_{∞} sin *θ*, with 0 ≤ *θ* ≤ *π*. The non-dimensional wall friction and the displacement thickness are obtained solving (17) and they are shown in figure 3 as a function of the polar angle *θ*, where *E*_{∞} = *ρU*^{2} and the exterior Reynolds number *Re*_{∞} = *U*_{∞}*D* / *ν* are computed using the sphere diameter *D* =2*A*, with wall friction where *Y* ^{3 }is the normal coordinate, and the displacement thickness *δ*^{*} is computed from

(18) |

**Figure 3**: Non-dimensional wall friction and displacement thickness as a function of *θ* using the potential velocity profile. The separation point is at *θ _{d}* ≈ 1.84 radians (≈ 105.45°).

The separation point is found at *θ _{d}* ≈ 1.84 radians (≈ 105.45°), in good agreement with the separation predictions given by a Rott-Cratree semi-analytical and a finite-difference computations, between 103.6° and 105.5°, respectively, as cited by White (2005).

On the other hand, for super-critical Reynolds numbers, the experimental velocity profile does not differ too much from the potential flow model altough there are flow separation effects. Since the axially symmetrical Blasius profile series is known up to the term *θ*^{7 }, the function sin *θ* is replaced by a series in odd powers giving a more realistic velocity profile. Thus, the actual velocity profile measured by Fage (1936) and cited by White (2005) at *Re* = 200 000 fits the curve

(19) |

for 0 ≤ *θ* ≤ 1.48, which drops off much faster than the potential one, reaching a maximum of* U / U _{∞}* =1.274 at

*θ*=1.291 radians (≈ 74° ) while the potential velocity profile has a maximum of

*U/U*= 3/2 at

_{∞}*θ*=1.571 radians (≈ 90°). The flow separation is reached at =1.424 radians (≈ 81.6° ), which is again in good agreement with the predictions given by a Rott-Cratree semi-analytical and a finite-difference computation, between 81.1° and 82.4° , respectively.

In the second flow case, the velocity profile given by (19) is again assumed, but the sphere has a steady spin ** ω** around an axis parallel to the constant velocity

**U**_{∞}, such as

*ωA / U*

_{∞}= 1. It is verified that whereas the inviscid streamlines are simply meridians, the limit viscous streamlines in this case have a tendency to rotate with the sphere, until they align with the separation streamline that is a parallel at = 1.47 radians (≈ 84.2° ) from the forward stagnation point, as it is shown in figure 4. Note that the spinning tends to stabilize the boundary layer against separation, resulting in a delay of almost 0.052 radians (≈ 3° ) with respect to = 1.424 radians (≈ 81.6° ). This is due to the centrifugal force that can be assimilated to a pressure gradient directed to the equator

*θ*→

*π*/ 2 radians (

*θ*→ 90°). Since the boundary layer separation in this case happens before the equator, this is equivalent to a favorable pressure gradient which has also a significant incidence in the viscous drag.

**Figure 4**: Computed limit viscous streamlines for the sphere of radius *A*, moving with a steady spin rotation *ω* around an axis parallel to the constant velocity *U*_{∞}, when *ωA*/*U _{∞}* = 1.

** VI. CONCLUSIONS**

An attached, laminar, isothermal steady flow without body forces of an incompressible viscous fluid of Newtonian type and constant physical properties has been considered. The boundary layer equations were first written in orthogonal extended curvilinear threedimensional coordinates *η*^{i}, with *i* =1, 2, 3. Next, the approximation for the two-dimensional surface coordinates *η*^{α}, with *α* =1, 2, were derived from the asymptotic properties of the metric tensor *g*^{ij} with respect to the dimensionless boundary layer thickness *δ*(*η*^{1},*η*^{2}), with . Six types of Christoffel symbols were found, depending on whether the affixes *i*, *j*, *k* are over the smooth surface, *η*^{1}and *η*^{2}, or along the normal direction *η*^{3 }. The order of these symbols with respect to the expansion parameter *δ* were estimated from the corresponding ones of the metric tensor, which are summarized in table 2. The well known consequence of zero pressure variation across the boundary layer is recovered in the continuity equation (second line in (17)). From a practical point of view, some advantages of writing the boundary layer equations in a covariant formalism in the three-dimensional Euclidean space are:

- It is more easy to check the physical units of each term and to detect errors due to mistakes in the approximations performed in the derivations;
- Any intrinsic curvature term is placed only in the covariant derivatives rather than displayed in the boundary layer equations in order to obtain a more clean physical picture and easier verification;
- There is not curvature terms in the boundary layer equations and it only remains the surface metric tensor
*a*^{ij}^{ }in the continuity equation; - It is a bit easier to change from one coordinate system to another in a three-dimensional Euclidean space, since there are not complicated curvature terms related to the non-Euclidean nature of the two-dimensional surface;
- The equations are covariant under a linear coordinate transformation on the two intrinsic surface coordinates
*η*^{1},*η*^{2}, and an arbitrary scaling of the normal coordinate*η*^{3 }to the body surface; - Finally, the covariant form also shows the well known properties of the boundary layer equations: a diffusive character on the normal coordinate
*η*^{3}and a wave-like one on the surface coordinates*η*^{1},*η*^{2}, that is, it has a dual intrinsic parabolic-hyperbolic nature.

** APPENDIX**

** A. Asymptotic orders in the covariant spatial metric tensor**

For a point ** y** ∈

*Γ*, the partial derivatives

*y*,

_{1},

*y*,

_{2}are parallel to the surface

*Γ*and, in the same way, the partial derivatives

*n*,

_{1}and

*n*,

_{2}are also parallel to the surface

*Γ*. Therefore, their scalar product with respect to the unit normal to the body surface

*are nulls, i.e. ⟨*

**n***∂*

*y*^{T}/

*∂η*

^{α},

**⟩ = 0 and ⟨**

*n**∂*

*n*^{T}/

*∂η*

^{α},

**⟩ = 0. There are three types of components in the covariant metric tensor g**

*n*_{ij}: surface, mixed and normal components. First, the surface components

*g*are written as

_{αβ}(A1) |

where

(A2) |

which are functions of the surface coordinates *η ^{1}*,

*η*. The first term a

^{2}_{αβ}gives the intrinsic components of the surface metric tensor. Note from Eq. (A1) that near the surface the components of the metric tensor

*g*are equal, at first order, to the intrinsic

_{αβ}*a*

_{αβ}ones. Next, the mixed components

*g*

_{α}_{3}are written as

(A3) |

Finally, the normal component *g*_{33} is reduced to

(A4) |

Then, using the asymptotic orders given by Eqs. (A1,A3,A4), the covariant metric tensor, expressed in matrix notation and partitioned as in Eq. (3), has the asymptotic expansion

(A5) |

where *a*_{αβ} =[*a*_{αβ}] ∈ , while * T* ,

*∈ , with*

**S** where *S* is a regular matrix whether *δ* > 0. Then, the first column of Table 1 is obtained from Eq. (A5).

** B. Asymptotic orders in the contravariant spatial metric tensor**

Using matrix notation, the contravariant metric tensor g^{ij} is computed from the covariant *g*_{ij} one using the relation *g*^{ij} = (*g*_{ij})^{−1 }. For this aim, it is convenient to introduce the decomposition

(B8) |

with

(B9) |

and

(B9) |

where *T*^{−1}= diag is regular if *a*_{αβ} is regular too. Then, using Eq. (A5, B8),

(B11) |

(B11) where the last line in Eq. (B11) produces the second column of Table 1.

**C. Asymptotic orders in the tangential component of the momentum equation**

The asymptotic orders in the tangential component of the momentum equation are determined as follows. First, the convective acceleration is given by

(C12) |

Next, the reduced pressure gradient is split in normal and tangential components, and taken into account the second line of Eq. (D23),

(C13) |

Finally, for the viscous dissipation, the first covariant derivative of *u*^{γ} is given by

(C14) |

As in the {*γ*, *h i*} symbol the special one {3, *β γ*} is not present, all the velocities *u*^{h} are assumed of *O*(1), and taking into account the asymptotic values in Table 1, it follows that

(C15) |

and from Eq. (C15), when *i* = 3,

(C16) |

The second covariant derivative of the tangential velocity *u*^{γ} is

(C17) |

in the first symbol on the r.h.s., the special case {3, βγ}is not present either except for the second symbol. There are four cases to be considered:

1. when *i*, *j* run over {1, 2},

(C18) |

2. when *i* = 3 and *j* ≠ 3,

(C19) |

3. the case *i* ≠ 3 and *j* = 3 is analogous to the previous one;

4. finally when *i* = *j* = 3,

(C20) |

Collecting Eqs. (C16, C18, C20) and using the standard assumption that the non-dimensional boundary layer thickness grows as which, in turn, is equivalent to *Re*^{−1} = *O*(*δ*^{2}), the dissipation of the tangential momentum is reduced to

(C21) |

** D. Asymptotic orders in the normal component of the momentum equation**

The asymptotic orders in the normal component of the momentum equation are determined as follows:

1. The convective acceleration is given by

(D22) |

2. The reduced pressure gradient is decomposed as

(D23) |

while .

3. For the viscous dissipation, the first covariant derivative of the normal velocity *u*^{3} is given by

(D24) |

which is split as

(D25) |

and

(D26) |

and the first covariant derivative of the tangential velocity *u*^{γ} is given by

(D27) |

The second covariant derivative of the normal velocity *u*^{3} is ∂u^{3}

(D28) |

There are four cases to be considered:

*i* when *i*, *j* run over {1, 2},

(D29) |

*ii* when *i* = 3 and *j* = 3,

(D30) |

iii the case *i* = 3 and *j* = 3 is analogous to the previous one;

iv finally when *i* = *j* = 3,

(D31) |

(D31) Collecting Eqs. (D29, D30, D31) and using again the standard assumption *Re*^{−1} = *O*(*δ*^{2}), the dissipation of the normal momentum is reduced to

(D32) |

** E. Asymptotic orders in the Christoffel symbols of first kind **

The Christoffel symbols of first kind are calculated with

(D33) |

there are six types of these symbols depending on whether the affixes *i*, *j*, *k* are over the smooth surface (*η*^{1}or *η*^{2}), or along the normal *η*^{3}. The order of these symbols with respect to the expansion parameter *δ*, with , are estimated from the order of the metric tensor as given as

(E34) | |

(E35) | |

(E36) | |

(E37) | |

(E38) | |

(E39) |

** F. Asymptotic orders in the Christoffel symbols of second kind **

The order of Christoffel symbols of second kind related to the expansion parameter *δ*, with , is also determined from the order of the metric tensor, as follows

(F40) | |

(F41) | |

(F42) | |

(F43) | |

(F44) | |

(F45) |

Note that in Eqs. (F40) there is only one special case given by the symbol {3, *β γ*} = *O*(*δ*^{−1}), while the remaining ones are *O*(*δ*) or *O*(*δ*^{2}), and that {*α*,*j k*} = *O*(*δ*).

** ACKNOWLEDGMENTS**

The authors would like to thank Diego Campana for his valuable comments about the manuscript. This work has received financial support from Consejo Nacional de Investigaciones Cientíıficas y Téecnicas (CONICET, Argentina, grant PIP 5271-05), Universidad Nacional del Litoral (UNL, Argentina, grant CAI+D 2009-III-4-2), Agencia Nacional de Promocióon Científica y Tecnológica (ANPCyT, Argentina, grants PICT 1506-06 and PICT 1141-07) and was performed with the Free Software Foundation/GNU-Project resources as GNU-Linux OS and GNU- Octave, as well as other Open Source resources as Scilab, TGif, Xfig and .

** REFERENCES**

1. Anderson, O. L. (1985). "Calculation of three- dimensional boundary layers on rotating turbine blades,". In Hamed, A., J. Herring, and L. Povinelli, editors, *Three-dimensional Flow Phenomena in Fluid Machinery*, **32**, 121-132. ASME. [ Links ]

2. Aris, R., *Vector, tensors, and the basic equations of fluid mechanics*, Dover (1989). [ Links ]

3. Battaglia, L., J. D'Elía, M. A. Storti, and N. M. Nigro, "Numerical simulation of transient free surface flows," *ASME-Journal of Applied Mechanics*, **73**, 1017-1025 (2006). [ Links ]

4. Bermúdez, L., A. Velázquez, and A. Matesanz, "Viscous-inviscid method for the simulation of turbulent unsteady wind turbine airfoil flow," *Journal of Wind Engineering and Industrial Aerodynamics*, **90**, 643-661 (2002). [ Links ]

5. Bogdanov, A. N. and V. N. Diyesperov, "The simulation of unsteady transonic flow and the stability of a transonic boundary layer," *Journal of Applied Mathematics and Mechanics*, **69**, 358-365 (2005). [ Links ]

6. Cebeci, T. and J. Cousteix, *Modeling and computation of boundary-layer flows*, Springer-Verlag (1999). [ Links ]

7. D'Elía, J., N. Nigro, and M. Storti, "Numerical simulations of axisymmetric inertial waves in a rotating sphere by finite elements," *International Journal of Computational Fluid Dynamics*, **20**, 673-685 (2006). [ Links ]

8. D'Elía, J., M. A. Storti, and S. R. Idelsohn, "A panel-Fourier method for free surface methods," *ASME-Journal of Fluids Engineering*, **122**, 309- 317 (2000). [ Links ]

9. Dey, J., "Constant pressure laminar, transitional and turbulent flows. an approximate unified treatment," *ASME Journal of Fluids Engineering*, **124**, 806-808 (2001). [ Links ]

10. Dwoyer, D. L., C. H. Lewis, and P. R. Gogineni, "A procedure for calculating laminar, transitional and/or turbulent three-dimensional boundary layers including surface curvature effects about arbitrary blunt-nosed bodies,"*Aerospace Sciences Meeting*, Huntsville, Ala. AIAA (1978). [ Links ]

11. Epureanu, B. I., K. C. Hall, and E. L. Dowell, "Reduced-order models of unsteady viscous flows in turbomachinery using viscous-inviscid coupling," *Journal of Fluids and Structures*, **15**, 255- 273 (2001). [ Links ]

12. Fage, A., "Experiments on a sphere at critical Reynolds numbers," Technical Report 1766, Aero. Res. Council, R and M, London (1936). [ Links ]

13. Fournier, G., F. Golanski, and A. Pollard, "A novel outflow boundary condition for incompressible laminar wall-bounded flows," *Journal of Computational Physics*, **227**, 7077-7082 (2008). [ Links ]

14. Frondelius, T., H. Koivurova, and A. Pramilay, "Interaction of an axially moving band and surrounding fluid by boundary layer theory," *Journal of Fluids and Structures*, **22**, 1047-1056 (2006). [ Links ]

15. German, B. J. A *Riemannian Geometric Mapping Technique for Identifying Incompressible Equivalents to Subsonic Potential Flows*. PhD thesis, Aerospace Engineering, Georgia Institute of Technology (2007). [ Links ]

16. Karimipanah, M. T. and E. Olsson, "Calculation of three-dimensional boundary layers on rotor blades using integral methods," *Journal of Turbomachinery*, **115**, 342-353 (1993). [ Links ]

17. Lakshminarayana, B., *Fluid Dynamics and Heat Transfer of Turbomachinery*, Wiley and Sons (1995). [ Links ]

18. Morgan, F., *Riemannian Geometry*, Jones Bartlett Publishers (1993). [ Links ]

19. Nicols, J. A. and J. M. Vega, "Three-dimensional streaming flows driven by oscillatory boundary layers," *Fluid Dynamics Research*, **32**, 119-139 (2003). [ Links ]

20. Pai, S., *Viscous Flow Theory*, van Nostrand Co (1956). [ Links ]

21. Panaras, R., "Boundary-layer equations in generalized curvilinear coordinates," Technical Report Technical Memorandum 100003, NASA, http://ntrs.nasa.gov/archive/nasa/casi.ntrs.nasa.gov/ (1987). [ Links ]

22. Pope, S. B., *Turbulent flows*, Cambridge, 2 edition (2003). [ Links ]

23. Prado, R., "Reformulation of the momentum theory applied to wind turbinnes," *Journal of Wind Engineering and Industrial Aerodynamics*, **58**, 277-292 (1995). [ Links ]

24. Reed, H. L. and R. S. Lin, "Effect of curvature on stationary crossflow instability of a three-dimensional boundary layer," *AIAA Journal*, **31**, 1611-1617 (1993). [ Links ]

25. Sagaut, P., *Large eddy simulation for incompressible flows*, Springer, Berlín (2001). [ Links ]

26. Schetz, J. A. (1991). "Numerical solution of the boundary layer equations using the finite element method,"*In Dhaubhadel, M. N., editor, Advances in Finite Element Analysis in Fluid Dynamics* **123**. ASME. [ Links ]

27. Schlitchting, H. and K. Gersten, *Boundary Layer Theory*, Springer, 8 edition (2004). [ Links ]

28. Smith, M. S., *Principles and applications of tensor analysis*, Howard W. Sams (1963). [ Links ]

29. Spurk, J. H., *Fluid mechanics*, Springer-Verlag, Germany (1997). [ Links ]

30. Stock, H., "Transition prediction in three-dimensional boundary layers on inclined prolate spheroids," *AIAA Journal*, **44**, 108-118 (2006). [ Links ]

31. Storti, M. (1998). "A pseudo-spectral approach for the incompressible boundary layer equations with automatic normal scaling,". In Idelsohn, S., E. Oñate, and E. Dvorkin, editors, *Computational Mechanics. New trends and applications*, 1-33. CIMNE, Barcelona, Spain. [ Links ]

32. Storti, M., J. D'Elía, and S. Idelsohn, "Algebraic Discrete Non-Local (DNL) absorbing boundary condition for the ship wave resistance problem," *J. Comp. Physics*, **146**, 570-602 (1998). [ Links ]

33. Storti, M. A. and J. D'Elía, "Added mass of an oscillating hemisphere at very-low and very-high frequencies," *ASME, Journal of Fluids Engineering*, **126**, 1048-1053 (2004). [ Links ]

34. White, F. M., *Viscous Fluid Flow*, McGraw-Hill, New York, 3rd edition (2005). [ Links ]

35. Wilcox, D. C., *Turbulence Modeling for CFD*, DCW, 2nd edition (1998). [ Links ]

**Received: October 11, 2009. Accepted: February 21, 2010. Recommended by Subject Editor Eduardo Dvorkin.**