SciELO - Scientific Electronic Library Online

 
 número28Deshidratacion osmotica de anana con reutilizacion del jarabe de SacarosaPretratamiento soda-etanol de pino y su influencia en la hidrolisis Enzimatica índice de autoresíndice de materiabúsqueda de artículos
Home Pagelista alfabética de revistas  

Servicios Personalizados

Revista

Articulo

Indicadores

  • No hay articulos citadosCitado por SciELO

Links relacionados

  • No hay articulos similaresSimilares en SciELO

Compartir


Revista de Ciencia y Tecnología

versión On-line ISSN 1851-7587

Rev. cienc. tecnol.  no.28 Posadas dic. 2017

 

INGENIERÍA, TECNOLOGÍA E INFORMÁTICA

Adsorption isotherm of dehydrated mashed cassava from different varieties

Isotermas de sorcion de pure deshidratado a partir de diferentes variedades de raiz

 

Maria M. Brousse1,*, Ramon A. Linares1, Maria L. Vergara1, Andrea B. Nieto2

1 Faculty of Exact, Chemistry and Life Sciences, National University of Misiones. Posadas, Argentina;
2 Faculty of Exact and Life Sciences, National University of Buenos Aires. Buenos Aires, Argentina.
* E-mail: brousse.mariamarcela@gmail.com


Abstract

Water sorption isotherms of two varieties of dehydrated mashed cassava, Conception and Pomberi, were determined for a temperature range between 25° C and 45° C. The dehydrated mashed cassava exhibited Type II behavior. Sorption isotherms showed that for aw values below 0.85, the sorption capacity decreased when temperature increased; opposite behavior was observed at aw above 0.85. The inversion point (aw = 0.85) was attributed to the fact that more active sites were exposed to the adsorption processes, due to the enhanced molecular mobility promoted in the amorphous regions by starch crystallization. The experimental data were fit to different sorption models. Model constants and correlation coefficients were obtained. BET, GAB and PELEG equations showed highest correlation coefficients for all range of aw. Total heat of sorption increased when moisture content decreased.

Key words: BET equations; Storage stability; Net isosteric heat; Nonlineal regression; Mathematical models.

Resumen

Las isotermas de sorcion de agua de pure de mandioca deshidratado de dos variedades de raices, Concepcion y Pomberi, se determinaron para un rango de temperatura entre 25° C y 45° C. El pure de mandioca deshidratado exhibio un comportamiento Tipo II. Las isotermas de sorcion mostraron que para valores de aw por debajo de 0.85, la capacidad de sorcion disminuyo cuando la temperatura aumento; comportamiento opuesto se observo a aw por encima de 0,85. El punto de inversion (aw = 0,85) se atribuyo al hecho de que los sitios mas activos se expusieron a los procesos de adsorcion, debido a que la movilidad molecular aumenta en las regiones amorfas por la cristalizacion del almidon. Los datos experimentales se ajustaron a diferentes modelos. Se obtuvieron las constantes de los modelos y los coeficientes de correlacion. Las ecuaciones BET, GAB y PELEG mostraron los coeficientes de correlacion mas altos para todos los rangos de aw. El calor de sorcion total aumento cuando disminuyo el contenido de humedad.

Palabras clave: Ecuaciones BET; Estabilidad de almacenamiento; Calor neto isosterico; Regresion no lineal; Modelos matematicos.


 

Nomenclature

A, B, C equations parameters (dimensionless)
aw water activity (dimensionless)
C0 pre–exponential factor (dimensionless)
∆H Arrhenius–type energy factor (kJ/mol)
∆Hc difference in heat of sorption between mono–layer and multi–layer (kJ/mol)
∆Hk difference between the heat of condensation of water and the heat of sorption of the multilayer (kJ/mol)
E % mean relative percentage
k0 pre–exponential factor (dimensionless)
k GAB model parameter (dimensionless)
k1 y k2 equation parameters (dimensionless)
MBE mean bias error
mi experimental value
mpi predicted value
n number of experimental data
n1 y n2 equation parameters (dimensionless)
R universal gas constant (8.314 (kJ/kmol K)
RMSE root mean square error
R2 coefficient determination
r2 coefficient correlation
T absolute temperature (K)
Tg the glass transition temperature
X equilibrium moisture content (g water/g dry solid)
Xm monolayer moisture content (g water/ g dry solid)
Xs security moisture content (g water/g dry solid)
Xmo pre–exponential factor (dimensionless)

Introduction

Cassava (Manihot esculenta Crantz) is considered a foodstuff of high nutritional value and one of the most economical sources of energy; because of carbohydrate yield is 40% greater than in rice and 20% greater than in corn (1). For this reason, processing of cassava root in order to obtain dehydrated mashed cassava was a product developed by a research group of Faculty of Exact, Chemistry and Life Sciences, National University of Misiones, and it is nowadays an alternative industrial production of the Agricultural and Industrial Cooperative San Alberto Ltd. in Province of Misiones, Argentina. Dehydrated mashed cassava is presented as a new food from Argentina to the world. It is a gelatinized product that will arrive to the market as dehydrated food, which when reconstituted with water; it is supposed to give a final product similar to cooked fresh root mashed cassava. In food, gelatinized starches can be used almost any time thickening is desired. The gelatinization of starch also significantly affects the characteristics and quality of food such as loaf volume and crumb bread, the elasticity and softness of paste products, digestibility and palatability, the tolerance of batter properties in cakes, frostings, and doughnut mixes, the sugar crystal growth in foods, and the texture, volume, shelf-life, and freeze-thaw stability of bread and cakes (2).
Sorption isotherms and sorption isosteric heat are the basic information for the foodstuffs drying model (3). Moisture sorption isotherm information is required for drying and storing food products. There is data in the literature on sorption behavior of starchy products (e.g., 4, 5) as well, water sorption data for cassava starch, such as the values presented by different authors (6), (7), (8). Sanni et al. (1997) (9) presented the sorption isotherm for two product off cassava roots processed, fufu and tapioca. However, the published literature about the sorption isotherms of dehydrated mashed cassava is nonexistent. Knowledge of the differential heat of sorption has a great importance in designing equipment for dehydration processes. Heat of vaporization of adsorbed water reaches values higher than the heat of vaporization of pure water when food is dehydrated to low moisture levels (10). Net isosteric heat is defined as the total heat of sorption in the food minus the heat of vaporization of water, at system temperature (11).
Heat of adsorption is a measure of the energy released on sorption, and the heat of desorption is the energy requirement to break the intermolecular forces between the molecules of water vapor and the surface of adsorbent (12). Thus, the heat of sorption is considered an indicator of the intermolecular attractive forces between the sorption sites and water vapor (13). To prepare the mashed dehydrated cassava, the roots are washed with water in a hopper. Then they are peeled in a cylindrical peeler whose walls are covered with abrasive material, eliminating the remains of peels with a water stream. The roots are cooked in a continuous cooker heated by steam and after cooking time the mashed is prepared by a press designed for the purpose. The mash is placed in trays and dried in a continuous dryer with hot air. Once the mash is dried, it is milled and sieved to homogenize the size and it is packed in packages of 0.2 or 25 kg bags according to their destination. There is a need to determine the sorption isotherms of mashed cassava to maximize their storage and to establish a reliable database for each of them. One important property of food product related to drying is its moisture sorption isotherm, since it will determine the degree of drying required to obtain a stable product (14).
The knowledge and understanding of sorption isotherms is highly important in food processing for the design and optimization of drying equipment, design of packages, predictions of quality, stability, shelf - life and for calculating moisture changes that may occur during storage. Several preservation processes have been developed in order to prolong the shelf - life of food products by lowering the availability of water to micro - organisms and inhibiting some chemical reactions (15). The main objective of this work is to evaluate the sorption isotherms of dehydrated mash from two different cassava varieties: Conception and Pomberí, at three different temperatures.

Data analysis

Different models are available in the literature for predicting adsorption isotherms in food (16). Models used in this study for describing the moisture sorption isotherm of mashed cassava samples are chosen too by the researchers who work with foods high in starch (17), (4), (18) and are presented in Table 1.

Table 1. Models for fitting the adsorption isotherms


Heat of sorption (Qs), calculated by the Clausius– Clapeyron equation, is used to estimate the total energy necessary during drying. Heat of sorption is a measure of the binding energy of absorbed water by the solid materials (19). The moisture content at which the total heat of sorption approaches the heat of vaporization of pure water is often taken as an indication of bound water in the foodstuff (20). At higher moisture contents, water is available for utilization by microorganisms because it is mechanically free in the void spaces of the system (21). As mentioned earlier the ‘‘net’’ isosteric heat of sorption is obtained from the differential equation of Clausius– Clapeyron, that is given by Eq. 1.

where T is the absolute temperature, aw is water activity, qst is net isosteric heat of sorption and R is the universal gas constant (R = 8.319 kJ/mol K).
Some of the models in Table 1 include the effect of temperature. Also, constants are in some cases related to certain properties. For example, in the GAB model, Xm is the monolayer moisture content (kg water/kg solid), and C and k are related to monolayer and multilayer properties. The effect of temperature on GAB constants were calculated from the Arrhenius equation, they are shown in Eqs. 2, 3 and 4 (30).

ΔH is an Arrhenius-type energy factor (kJ/mol K); ΔHc: H1-Hm = heat of sorption of the first layer –heat of sorption of a multilayer (kJ/mol K); ΔHk: HL–Hm= heat of condensation of pure water vapor –heat of sorption of a multilayer (kJ/mol K); Xmo, k0 y C0 are pre-exponential factors.

Materials and Methods

Raw material
Dehydrated mashed cassava of Conception and Pomberí varieties were obtained from San Alberto Ltd., Misiones, Argentina.

Determination of equilibrium moisture content
The equilibrium moisture content of dehydrated mashed cassava of two varieties, Conception and Pomberí, was obtained by the static gravimetric method, as described by (31), at temperatures of 25, 35 and 45º C. The glass sorption jars were placed in a temperature controlled cabinet, with an accuracy of ±1º C at the selected temperatures. The temperatures were chosen to simulate variation in temperature across the country. Triplicate mashed samples (3 ± 0.001 g), were put into small crucibles and placed in desiccators with saturated salt solutions of water activity between 0.11–0.97. The salts used were LiCl, KF2, NaI, NaBr, KI2, NaCl, KCl, K2SO4. Thymol was placed in the desiccators containing NaCl and BaCl2 in order to prevent the growth of mould (32). The samples were weighed within interval of 24 hours and allowed to equilibrate until there was no discernible weight change, as evidence by constant weight values (± 0.002g). The dry mass was determined gravimetrically. The time required for equilibrium was fifteen and twenty days.

Data analysis
A non-linear least square regression analysis was used to evaluate the model parameters. To evaluate the goodness of fit of each model, root mean square error (RMSE), the mean bias error (MBE), the coefficient determination (R2) and the mean relative percentage deviation modulus (E) was used, which is defined by Eqs. 5, 6 and 7.

where mi is the experimental value, mpi is the predicted value, and n is the number of experimental data. A good fit is indicated by small values of RMSE and MBE and the mean relative percentage deviation modulus (E) below 10% indicative of a good fit for practical purposes (33).

Results and Discussion

All adsorption isotherms presented an increase in the equilibrium water content along with an increase in aw (Figure 1). The sigmoidal shape found is typically reported as a Type II isotherm (34), according to Brunauer’s classification (35). The class II isotherms can be interpreted as a superposition of the localized monolayer adsorption on the internal material surface and the dilution of some part of the solids in solution (36). The mathematical expressions were developed for polymer hydration by (37). Similar behavior was found in some fortified cassava products (38), in cassava starch (6), (7), (39), (9), (17), potato starch (4), (40), (7), (41), corn starch (40), (41), (42) and in starches modified of cultivars of cassava (43).


Figure 1:
Sorption isotherms of dehydrated mashed cassava for a temperature range between 25 and 45 C ( 25 º C, 35 º C, 45 º C) for Conception and Pomberi varieties. Modified GAB fits are represented on the graph (solid line 25 º C, dash line 35 º C and dotted line 45 º C).

Figures show that for water activity values below 0.85, the equilibrium moisture content decreases when temperature increases, which was expected in an exothermic moisture adsorption process (at constant water activity), indicating that the dehydrated mashed cassava become less hygroscopic. However, for aw values higher than 0.85 an isotherm cross-over with temperature is observed, i.e., the equilibrium moisture content increased with temperature for a given aw value. Similar crossing was reported in cassava starch (17), (44); cornmeal, (45); potato starch (46) and wheat flour (18). It was observed that dehydrated mashed cassava samples stored at room temperature tended to crystallize when they were conditioned at high relative humidity. All of these authors reported this behavior and attributed it to the endothermic dissolution of sugars at elevated water activity. Nevertheless, the material considered here is neat starch, for which the isotherm inversion with temperature at high water activity (or moisture content), could be more related to a greater exposure of active sites or hydrophilic groups at high aw or water contents as the temperature increases, as indicated by Brett and Figueroa (48). These authors presented evidence that relates the isotherm cross-over of oat flour and rice flour with temperature, to the onset of glassy to rubbery state transition taking place for the highest temperature sorption curve at high moisture contents or aw’s. On the other hand, at 45º C (the highest temperature tested in this work), it is assumed that samples stored at high humidity, could show a possible crystallinity development upon conditioning at that temperature. These results are similar to reported at Perdomo (17) in cassava starch. Hence, it can be suggested that as water is being squeezed out of the crystals due to the crystallization process, the amount of water adsorbed into the rubbery amorphous starch matrix of dehydrated mashed cassava will be greater, which in turn, due to its plasticizing effect will increase molecular mobility. Consequently, an increase of the available hydroxyl groups for sorption enhancement will be promoted. The deviation in the sorption capacity of starches as possibly linked to the onset of the glass transition range has also been previously suggested in the literature (57), (4), (48).
Sorption data for dehydrated mashed cassava is not available in the literature. Nevertheless, sorption data for cassava starch have been presented at one temperature, normally at room temperature (6), (7), (8), (41). Besides, water adsorption isotherms for cassava bagasse are presented (47). Nonetheless, results presented in this work for amorphous cassava starch are in line with the crossover/ Tg relationship reported by (48) and cassava starch reported by (17). Moisture sorption isotherm for dehydrated mashed cassava obtained at three temperatures (25º C, 35º C and 45º C), were fitted to models the Table 1 and the results are shown in Table 2.

Table 2. Fitting parameters for the mathematical expressions applied to sorption data of dehydrated mashed cassava at different temperatures. (C: Conception Variety; P: Pomberí Variety)


Table 2 shows that, except from the CAURRIE, FERRO FONTAN and HALSEY models fitted at 45 º C, models described well the experimental sorption behavior of mashed dehydrated cassava in the range of temperatures considered, as indicated by R2 values greater than 0.90, small values of RMSE and MBE and mean relative errors lower than 10%. These results are similar to reported for potato (4), (41); tapioca grits (44); cassava starch (17) and cassava bagasse (47). BET and GAB equations showed that the monolayer water content decreased when the temperature increased for both varieties. This fact has been attributed in the literature to a reduction of the active sites in the food matrix due to chemical and physical changes (e.g., reduction in hydrogen bonding degree), taking place as the temperature increases, the extension of which will depend on food nature (4), (49). The monolayer water content values obtained by the GAB model were higher than those obtained by the BET model. As expected, BET model refers to adsorption in the monolayer, however in GAB model the properties of water adsorbed in multilayer are considered (18).
GAB model has an advantage as compared to the BET model since it offers an objective method for drawing sorption isotherms up to 0.9 aw while the BET model is limited to 0.2–0.6 aw (50). The values of monolayer water content reported for dehydrated mashed cassava were lower than those found by (7), for native cassava starch at 25° C (0.074 using BET model and 0.079 by the GAB model). These differences could be attributed to the fact that starch in mashed dehydrated cassava is completely gelatinized. X parameter in CAURIE model is called “the security moisture content value” and it is important from a commercial point of view because it provides the maximum moisture content for the food during a possible storage and packing. In our study for both varieties, Conception and Pomberí, X values are similar to Xm values of GAB equation. It should be noted that, although the PELEG models provide a good representation of the data, they provide no indication of the nature of the sorption process (4). The temperature dependencies of the GAB constants calculated using linear regression are shown in Table 3.

Table 3. Characteristic GAB parameters for mashed dehydrated cassava

ΔHc represents the difference in enthalpy between mono-layer and multi-layer sorption (36). The positive value calculated is due to the strong exothermic interaction of water vapor with the primary sorption sites of starch matrix. ΔHk represents the difference between the heat of condensation of water and the heat of sorption of the multi-layer. The relatively lower magnitudes of ΔHk observed implies the presence of less firmly bound multilayer molecules, at intermediary energy levels between those of mono-layer molecules and the bulk liquid. The small negative value of ΔHk indicates that the heat of sorption of the multi-layer is greater than the heat of condensation of water, due to the endothermic dissolution of small molecular solutes (4) and it is related to isotherm cross-over behavior with temperature. Values of the heat of sorption at a specific moisture content provides an indication of the state of the sorbed water and hence, a measure of the physical, chemical and microbiological stability of the food material under given storage conditions (51). This provides valuable data for energy consumption calculations and subsequent design of drying equipment, and knowledge of the extent of the water–solid versus water–water interactions (52). The net isosteric heat of sorption values with respect to moisture content are represented in Figure 2, for both varieties.


Figure 2:
Variation of the isosteric heat of sorption of dehydrated mashed cassava with moisture content, Pomberi variety in solid line and conception variety in dash line.

The plot exhibits a steep initial drop in the monolayer region, continues to decrease smoothly as the multilayers are formed and finally approaches to zero at moisture levels of about 0.20 g water/g dry basis. The decrease in the isosteric heats with the amount of water sorbed can be qualitatively explained by considering that sorption initially occurs on the most active sites giving rise to the greatest interaction energy. As the moisture content increases, the sites available for sorption of water diminish, resulting in lower values of Qst. (11), (53), (54). Variations of the isosteric heat of sorption with moisture contents (X) can be expressed as:

Conception

Pomberí

It has been established that during the initial stages of the sorption process at low moisture content, there are more active sites on the food surface covered by a monolayer of water, with a higher energy of binding than those existing at higher moisture content (multilayer water) (55), (56), (17).

Conclusions

The water sorption behavior of dehydrated mashed cassava of two varieties of roots, Conception and Pomberí, was evaluated in order to optimize drying kinetics and minimize the energy expenses involved in dehydration processes. The adsorption isotherms obtained in this work presented the sigmoid shape. The adsorption isotherms of dehydrated mashed cassava were studied in temperatures from 25 to 45 °C, presenting increasing values of equilibrium moisture content when relative humidity increased and temperature decreased. The inversion (or cross-over) points, exhibited at a water activity of around 0.85, were explained by the result of more active sites exposed in virtue of the enhanced molecular mobility due to the water squeezed out of the crystals upon crystallization. The correlation coefficients (R2) obtained for each model studied showed correlation coefficients above 0.98. The GAB, BET and PELEG models were more appropriate. The monolayer water content, if determined by GAB model, was found to be inversely related to temperature and their values ranging from 0.049 to 0.039 and 0.05 to 0.043 g/g (dry basis) for dehydrated mashed at Conception and Pomberí varieties, respectively. Estimates of isosteric heat of sorption and their variation with moisture content were also presented for both mashed varieties.
An exponential relationship was found to describe this variation, within the moisture content range considered in this work.

References

1. Tonukari, N. Cassava and the future of starch. Electronic Journal of Biotechnology. 7(1): p. 5–8. 2004.

2. Chiang, B. Y. and Johnson, J. A. Gelatinization of starch in extruded products. Cereal Chemistry. 54: p. 436-443. 1977.         [ Links ]

3. Chen, C. Obtaining the isosteric sorption heat directly by sorption isotherm equations. Journal of Food Engineering. 74(2): p. 178–185. 2006.

4. Al-Muhtaseb, A. H.; McMinn, W. and Magee, T. Water sorption isotherm of starch powders Part 1: Mathematical description of experimental data. Journal of Food Engineering. 61(3): p. 297–307. 2004a.

5. McMinn, W. A. and Magee, T. R. Studies on the effect of temperature on the moisture sorption characteristics of potatoes. Journal of Food Process Engineering. 22: p. 113–128. 1999.

6. Chang, Y.; Cheah, P. and Seow, C. Plasticizing effects of water on physical properties of tapioca starch films in the glassy state. Journal of Food Science. 65: p. 445–451. 2000.

7. Chatakanonda, C.; Dickinson, L. and Chinacohoti, P. Mobility and distribution of water in cassava and potato starches by H and H NMR. Journal of Agricultural and Food Chemistry. 51: p. 7445–7449. 2003.

8. Mali, S.; Sakanaka, L. S.; Yamashita, F. and Grossmann, M. V. E., Water. sorption and mechanical properties of cassava starch films and their relation to plasticizing effect. Carbohydrate Polymers. 60: p. 283–289. 2005.

9. Sanni, L.; Atere, C. and Ayoade, K. Moisture sorption isotherms of fufu and tapioca at different temperatures. Journal of Food Engineering. 34: p. 203–212. 1997.

10. King, C. J. Rate of moisture sorption and desorption in porous, dried foodstuffs. Food Technology. 22: p. 509–514. 1968.

11. Tsami, E.; Maroulis, Z. B.; Morunos-Kouris, D. and Saravacos, G. D. Heat of sorption of water in dried fruits. International Journal of Food Science and Technology. 25: p. 350–359. 1990.

12. Rizvi, S. S. H. Thermodynamic properties of food in dehydration. In: M. Rao, M., and S., Rizvi, (2nd ed.). Engineering properties of food. NewYork: Marcel Dekker Inc p. 223–309. 1995.

13. Wang, N. and Brennan, J. G. Moisture sorption isotherm characteristics of potatoes at four temperatures. Journal of Food Engineering. 14: p. 269–282. 1991.

14. Sereno, A.M.; Moreira, R. and Martinez, E. Mass transfer coefficients during osmotic dehydration of apple in single and combined aqueous solutions of sugar and salt. Journal of Food Engineering. 47: p. 43–49. 2001.

15. Siripatrawan, U. and Jantawat, P. Determination of moisture sorption isotherms of jasmine rice crakers using BET and GAB models. Food Science Technology. 12: p. 459–465. 2006.

16. Iglesias, H. A. and Chirife, J. An empirical equation for fitting water sorption isotherms of fruits and related products. Canadian Institute of Food Science and Technology Journal. 11: p. 12–18. 1978.

17. Perdomo, J.; Cova, A.; Sandoval, A. J.; Garcia, L.; Laredo, E. and Muller, A. J. Glass transition temperatures and water sorption isotherms of cassava starch. Carbohydrate Polymers. 76: p. 305-313. 2009.         [ Links ]

18. Erbas, M.; Ertugay, M. and Certel, M. Moisture adsorption behaviour of semolina and farina. Journal of Food Engineering. 69: p.191-198. 2005.         [ Links ]

19. McLaughlin, C.P. and Magee, T.R. The determination of sorption isotherm and the isosteric heats of sorption for potatoes. Journal of Food Engineering. 35(3): p. 267- 280. 1998.         [ Links ]

20. Kaymak-Ertekin, F. and Sultanoglu, M. Moisture sorption isotherm characteristics of peppers. Journal of Food Engineering. 47: p. 225-231. 2001.         [ Links ]

21. Fasina, O. O. and Sokhansanj, S. Equilibrium moisture relations and heat of sorption of Alfafa Pellets. Journal of Agriculture Engineering Research. 56: p. 51–63. 1993.

22. Aguerre, R. J.; Suarez, C. and Viollaz, P. New BET Type Multilayer Sorption Isotherms. Part: Modelling Water Sorption in Foods. Lebensmittel-Wissenschaft und- Technologie. 22: p. 192-195. 1989.         [ Links ]

23. Ferro Fontan, C.; Chirife, J.; Sancho, E. and Iglesias, H. A. Analysis of a model for water sorption phenomena in foods. Journal Food Science. 47: p. 1590. 1982.         [ Links ]

24. Anderson, R. Modifications of the BET equation. Journal of the American Chemical Society. 68: p. 686–691. 1946.

25. Guggenheim, E. Applications of statistical mechanics, 1966. In: M. Rao, M. and S., Rizvi, (2nd ed.). Engineering properties of food. NewYork: Marcel Dekker Inc. p. 251. 1995.         [ Links ]

26. De Boer, J. (1953). The dynamic character of adsorption. Clarendon Press. Also In: Rao, M. and Rizvi, S., Engineering properties of food (2nd ed.). NewYork: Marcel Dekker Inc. p. 251. 1995.         [ Links ]

27. Hasley, G. Physical adsorption in non-uniform surfaces. Journal of Chemistry and Physics. 16: p. 931–945. 1948.

28. Henderson, S. A basic concept of equilibrium moisture. Agricultural Engineering. 33(1): p. 29–31. 1952.

29. Peleg, M. Assessment of a semi-empirical four parameter general model for sigmoid moisture sorption isotherms. Journal Food Process Engineering. 16: p. 21–37. 1993.

30. Kim, S. S. and Bhowmik, S. R. Moisture sorption isotherms of concentrated yogurt and microwave vacuum dried yogurt powder. Journal of Food Engineering. 21: p. 157-175. 1994.         [ Links ]

31. Pawar, V. S.; Pawar, D. K.; Rodge, V. D.; Surve, V. D. and More, D. R. Moisture adsorption isotherms of ground turmeric at different temperature. Journal of Food Science and Technology. 29: p. 170-173. 1992.         [ Links ]

32. Klewicki, R.; Konopacka, D.; Uczciwek, M.; Irzyniec, Z.; Piasecka, E. and Bonazzi, C. Sorption isotherms for osmo-convectively- dried and osmo-freeze-dried apple; sour cherry and blackcurrant. The Journal of Horticultural Science and Biotechnology. Isafruit Special Issue: 75-79. 2009.         [ Links ]

33. Lomauro, C. L.; Bakshi, A. S. and Labuza, T. P. Evaluation of food moisture sorption isotherms equation. Part I: Fruit, Lebensmittel - Wissenschaft und Technologies. 18: p. 111-117. 1985.         [ Links ]

34. Al-Muhtaseb, A.; McMinn, W. and Magee, T. Moisture sorption isotherm characteristics of food products: A review. Transactions of the Institution of Chemical Engineers Part C. 80: p. 118–127. 2002.

35. Brunauer, S.; Deming, L. S; Deming, W. E. and Troller, E. On the theory of Van der Waals adsorption of gases. Journal of the American Chemical Society. 62: p. 1723–1732. 1940.

36. van den Berg, C. Description of water activity of foods for engineering purposes by means of the G.A.B. model of sorption. In: McKenna, B. M., Engineering and Foods. Pp. 311-321. New York: Elsevier. 1984.         [ Links ]

37. Hailwood, A. J. and Horrobin, S. Absorption of water by polymers: Analysis in terms of a simple model. Transactions of the Faraday Society, 42B: p. 84-102. 1946.         [ Links ]

38. Sanni, L. and Kuye, A. Effect of temperatures on water sorption isotherms of some fortified cassava products, Proceedings of the 12th International Drying Symposium IDS2000, ed by Kerkhof PJAM, Coumans WJ and Mooiweer GD. Elsevier Science, Amsterdam, Paper 23. 2000.         [ Links ]

39. Sanni, L.; Atere, C. and Kuye, A. Moisture Sorption Isotherms of Fufu and Tapioca at Different Temperatures. Journal of Food Engineering, 34: p. 203-2012. 1997.         [ Links ]

40. Boki, K. and Ohno, S. Equilibrium isotherm equations to represent moisture sorption on starch. Journal of Food Science. 56: p. 1106–1110. 1991.

41. Mishra, S. and Rai, T. Morphology and functional properties of corn, potato and tapioca starches. Food Hydrocolloids. 20: p. 557–566. 2006.

42. Palou, E.; Lopez-Malo, A. and Argaiz, A. Effect of temperature on the moisture sorption isotherms of some cookies and corn snack. Journal of Food Engineering. 31: p. 85–93. 1997.

43. Osundahunsi, O. F.; Seidu, K. T. and Mueller, R. Effect of presence of sulphurdioxide on acetylation and sorption isotherm of acetylated starches from cultivars of cassava. Food Chemistry. 151: p. 168–174. 2014.

44. Adebowale, A. R.; Sanni, L.; Awonorin, S.; Daniel, I. and Kuye, A. Effect of cassava varieties on the sorption isotherm of tapioca grits. International Journal of Food Science and Technology. 42: p. 448–452. 2007.

45. Vega-Galvez, A.; Lara-Aravena, E. and Lemus-Mondaca, R. Isotermas de adsorción de harina de maíz. Ciência e Tecnologia de Alimentos. 26: p. 821-827. 2006.         [ Links ]

46. Viollaz, P. E. and Rovedo, C. O. Equilibrium sorption isotherms and thermodynamic properties of starch and gluten. Journal of Food Engineering. 40(4) : p. 287–292. 1999.

47. Polachini, T. C.; Betiol, L.; Lopes-Filho, J. and Telis-Romero, J. Water adsorption isotherms and thermodynamic properties of cassava bagasse. Thermochimica Acta. 632: p. 79–85. 2016.

48. Brett, B. and Figueroa, M. Moisture sorption characteristics of starchy products. Oat flour and rice flour. B.Sc. thesis, Simón Bolívar University, Venezuela (in Spanish) (2005).         [ Links ]

49. Aviara, N. A., and Ajibola, O. O. Thermodynamics of moisture sorption in melon seed and cassava. Journal of Food Engineering. 55(2): p. 107–113. 2002.

50. Timmermann, E. O.; Chirife, J. and Iglesias, H. A. Water sorption isotherms of foods and foodstuffs: BET or GAB parameters? Journal of Food Engineering. 48: p. 19– 31. 2001.

51. Ciro, H.; Osorio, J. and Cortes, E. Determination of the isosteric heat to plantain pulp (musa paradisiaca) by sorption isotherms. Dyna. 156: p. 127-134. 2008.         [ Links ]

52. McMinn, W. A. and Magee, T. R. Thermodynamic properties of moisture sorption of potato. Journal of Food Engineering. 60: p. 155–157, 2003.

53. Delgado, A. E., and Sun, D.W. Desorption isotherms for cooked and cured beef and pork. Journal of Food Engineering. 51: p. 163– 170. 2002b.

54. Jayendra Kumar, A.; Singh, R. R. B.; Patil, G. R. and Patel, A. A. Effect of temperature on moisture desorption isotherms of kheer. Lebensmittel-Wissenschaft und-Technologie. 38: p. 303–310. 2005.

55. Al-Muhtaseb, A. H.; McMinn, W. and Magee, T. Water sorption isotherm of starch powders Part 2: Thermodynamic characteristics. Journal of Food Engineering. 62(2): p. 135–142. 2004b.

56. Iglesias, H. A. and Chirife, J. Isosteric heat of water vaporsorption on dehydrated foods Part I: Analysis of the differential heat curves. Lebensmittel-Wissenschaft und-Technologie. 9: p. 116–122. 1976.

57. Van den Berg, C. (1981). Vapour sorption equilibria and other water–starch interactions: Physico–chemical approach. Ph.D. Thesis, Agricultural University Wageningen, The Netherlands. In Al-Muhtaseb et al. (2004a).

Recibido: 31/05/2017.
Aprobado: 13/10/2017.

Creative Commons License Todo el contenido de esta revista, excepto dónde está identificado, está bajo una Licencia Creative Commons